BPL Defibrillators Biphasic Monitoring Screens - Relife 900/AED/R
In stock
SKU
MBBPLM0014
- Allows the clear and precise display of multiple waveforms and defibrillation parameters
- Continuous voice prompts and on screen messages to aid in revival and resuscitation process
- The current controlled bi-phasic waveforms lowers the electrical threshold for successful defibrillation, besides adjusting for impedance
- Metronome signal for synchronizing chest compression during CPR
- 100 charge / discharge of 300J with fully charged new battery
- Synchronized Cardioversion function is available for providing defibrillation on sync with ECG waveform
- 2-300 J of energy level can be selected for defibrillation by the user
- Memorises always the last 24 Critical Event ECG information which can be viewed or recorded+N3
- Remote energy selection, charging and discharging through paddles facilitate convenient usage
- Patient-Paddle quality of contact is provided on screen Optional Enhancements:
- Accurate monitoring of breath rate along with CO2. It comes with Mainstream or Sidestream Option.
- Accurate SpO2 measurements powered by MasimoSET
- In Automated External Defibrillator (AED) mode, the shock sequence can be selected based on the requirement
- Accurate NIBP measurements powered by SunTech
Specifications:
| Model No | Relife 900/AED/R |
|---|---|
| Manual Defibrillator | |
| Defibrillator Waveform | Current Controlled, Biphasic |
| Energy Selection Option | 2-300J in steps of 2, 3, 5, 7, 10, 20, 30, 50, 70, 100, 150, 200, 250, 300 Joules |
| Energy Selection Control | Selected using keys located on the front panel or on the sternum paddle. |
| Paddle Assembly | Detachable type external paddle assembly with coiled retractable high voltage cable Adult & paediatric paddles integrated into same handle |
| Charge Control | Control on the front panel and on the apex paddle. |
| Synchroniser | Energy is delivered within 50 msec of the detected R-wave peak. SYNC message displayed on screen. Sync LED illuminates in Sync mode & blinks during each detected QRS wave Sync marker appears on both screen and recorder strip |
| Patient Impedance | 25–200 ohms:Actual patient impedance during shock is displayed on the screen |
| Charge Time | 300 Joules in less than 7 seconds when connected to AC mains 300 Joules in less than 9 seconds with a fully charged new battery |
| AED (Optional) | |
| Shock Sequence | Low-Low-Low/Low-Low-High/Low- High-High Low - 200J and High - 300J (Programmable) |
| Analysis Control | Automatic on attaching electrodes. Additional control on the front panel to restart rhythm analysis |
| AED Mode Usage Guidance | Though voice prompts and on screen text messages |
| Shock delivery | Through external disposable electrodes suitable for patients with weight >25 Kgs. |
| Shock delivery Control | Control on the front panel with blinking LED |
| ECG analysis time | < 15 seconds |
| Impedance measurement | Verifies electrode contact |
| Movement and artefact detection | Continuous examination of signal quality |
| VF/VT Sensitivity | > 90% |
| Specificity | > 95% |
| Monitor | |
| Display | 7 inch Colour TFT |
| Sweep speed | 25 ± 1 mm/sec |
| ECG Input modes | ECG input through Paddles or ECG Patient cable. |
| ECG Lead selection | 3 Lead or 5 Lead cable |
| Leads off indication | LEADS OFF message displayed on the screen. |
| User gain settings | 8 level setting 2.5, 5, 7.5, 10, 15, 20, 30 & 40 mm/mV |
| Reset recovery | Automatic recovery of waveform within 0.5seconds after overload or defibrillation |
| Pace pulse recognition | Detects and rejects pace maker pulses of amplitude between ±2mV and ±700mV and duration between 100microseconds and 2milli seconds. |
| Common mode rejection | >90 dB at 50Hz |
| Input impedance | >2.5 Mohm |
| Frequency response | 0.5 to 40 Hz |
| Heart rate display | 10 to 300 BPM; Accuracy ±2 BPM or 2% whichever is higher. |
| QRS tone | Audible tone with every detection of QRS. Beep volume can be adjusted by users. |
| Defibrillator protection | Available |
| ECG trace freeze | Available & Freezes the ECG trace on the screen. MARK key can be configured to freeze and remove freeze condition. HR, SpO2, NIBP display and Alarms are active in freeze mode. |
| Single Channel Thermal Recorder (Optional) | |
| Paper speed | 25 ± 1 mm/sec |
| Paper size and type | Thermal paper in rolls. 58 mm width, 15 meters. |
| Event recording | Stores and prints 3 seconds pre critical data and 7 seconds post critical event data up to 24 events. Data is retained even after the unit is turned off. |
| Recorder mode | Configurable to print either real time or 6 seconds delayed ECG. |
| Memory | |
| Event information | Last 24 critical events are stored along with ECG information. Events include MARK key press, Shock delivery and HR Alarm violation. |
| Trend | Last 200 NIBP measurement data and last 200 Alarm violation information. |
| Power and Battery | |
| AC input | 100 – 240Vac, 50/60 Hz & < 240 VA |
| Battery | Sealed Lead Acid 12V, 4.5AH; >100 discharges of 300 Joules (With Fully Charged New Battery) |
| Safety | |
| Classification | Class I with internal power supply as per IEC 60601-1 |
| Degree of protection | |
| ECG - Type CF | |
| SpO2 - Type BF | |
| NIBP - Type BF | |
| Paddle - Type BF | |
| Physical and Environmental | |
| Dimensions | 370mm (W) x 300mm (D) x 290mm (H) |
| Weight | Less than 8.5Kg. (including battery, external paddles ) |
| Operating temperature | 0 to 40° C |
| Storage temperature | -10 to 60° C (except disposable electrodes) |
| Relative humidity (operating and storage) | 15 to 95% non-condensing |
| MasimoSET SpO2 (Optional) | |
| SpO2 | |
| SpO2 Range | 1 – 100% |
| Resolution | 1% |
| Accuracy (During no motion conditions) | 70 – 100% ± 2%, in Adults and Paediatrics 0 – 69%, unspecified |
| Accuracy (During motion conditions) | 70 – 100% ± 3%, in Adults and Paediatrics 0 – 69%, unspecified |
| Averaging time | 2-4 / 4-6 / 8 / 10 / 12 / 14 / 16 Seconds (User selectable) |
| Pulse Rate | |
| Range | 25 – 240 bpm |
| Resolution | 1 bpm |
| Accuracy (During no motion conditions) | ± 3 bpm |
| Accuracy (During motion conditions) | ± 5 bpm |
| Perfusion Index Resolution | 0.01% |
| Low perfusion performance (>0.02% Pulse Amplitude and % Transmission > 5%) | Saturation(%SpO2) ± 2% Pulse Rate ± 3 bpm |
| Masimo ETCO2 (Optional) | |
| ETCO2 (Mainstream Module) | |
| Measurement Method | Infrared Spectrum |
| Measurement Range | 0 - 15% |
| Resolution | 0.1% |
| Unit | % mmHg |
| Accuracy | ± 0.2 Vol % + 2% of reading |
| Warm up time | < 10 seconds |
| Rise Time | ?90ms |
| awRR measurement range | 0 - 150bpm |
| awRR measurement accuracy | ± 1bpm |
| Total system response time | < 1 second |
| ETCO2 (Sidestream Module) | |
| Measurement range | 0 - 15% |
| Resolution | 0.1% |
| Unit | %, mmHg |
| Accuracy | ± 0.2 Vol % + 2% of reading |
| Warm up time | < 10 seconds |
| Rise Time | ? 200ms |
| awRR measurement range | 0 - 150bpm |
| awRR measurement accuracy | ± 1bpm |
| Sample flow rate | 50 ml/min ± 10ml/min |
| Total system response time | < 3 secs |
| Suntech NIBP (Optional) | |
| Method | Oscillometric |
| Operating Modes | Manual, Automatic and Stat Blood Pressure Range |
| Systolic | Adult, 40 – 250 mmHg, Paediatric, 40 – 230 mmHg |
| Diastolic | Adult, 20 – 200 mmHg, Paediatric, 20 – 160 mmHg |
| MAP (Mean Atrial Pressure) | Adult: 26 – 220 mmHg, Paediatric: 26 – 183 mmHg |
| Cuff Pressure Measurement Range | 0 to 300 mmHg |
| Initial Inflation Pressure | Adult, 160 mmHg, Paediatric, 140 mmHg |
| Pressure Transducer Accuracy | ± 3 mmHg or 2% of the reading whichever is greater |
| Cycle Time in Auto mode | 1, 2, 3, 5, 10, 15, 30, 60, 90 Minutes (User selectable) |
| Cycle Time in Stat mode | 5 Minutes |
| Maximum Inflation Time | 75 Seconds |
| Blood Pressure Accuracy | Meets accuracy requirements of ANSI/AAMI SP10:2002(R)2008, |
| EN1060-4:2004 and ISO 81060-2-2009 standards |
| BRAND | BPL |
|---|
Write Your Own Review
